Efficiency Enhancement of CIGS Solar Cells with the Appropriate Combination of CdS and CdSe Buffer Layers: Simulation by Silvaco Software

Authors

Abstract

The buffer layer is one of the main elements in the thin film solar cells, especially in the copper indium gallium selenide (CIGS) thin-film solar cells. The buffer layer increases the optical absorption and decreases the surface recombination, which in turn results in further absorption of carriers and the enhancement of the solar cell efficiency. In this paper, the cadmium sulfide (CdS) and cadmium selenide (CdSe) thin films were selected as buffer layers. Then, the effect of different combinations of these two buffer layers on the solar cell parameters such as JSC, VOC, FF, and η were investigated using Silvaco Atlas commercial software. The optimal condition and higher efficiency were achieved when the CdS and CdSe layers were close to the ZnO and CIGS layers respectively. It was found out that the selection of 40-nm thickness for cadmium sulfide and 10-nm thickness for cadmium selenide increased the efficiency of solar cell up to 25.19%. Also, the plotting of the energy band diagram illustrated that electrons and holes, in an optimal condition, moved easily without any potential barriers. This condition led to a significant increase in the solar cell efficiency.

Keywords

References

[1] Pettersson, J., Modelling band gap gradients and Cd-free buffer layers in Cu (In, Ga) Se2 solar cells, Ph.D. Thesis, Acta Universitatis Upsaliensis, 2012. [2] Camacho-Espinosa, E., López-Sánchez, A., Rimmaudo, I., Mis-Fernández, R. and Peña, J. L., All-sputtered CdTe solar cell activated with a novel method", Solar Energy Vol. 193, pp. 31-36, 2019. [3] Ahmad, F., Anderson, T. H., Monk, P. B. and Lakhtakia, A. "Efficiency enhancement of ultrathin CIGS solar cells by optimal bandgap grading: erratum", Applied optics, Vol. 59, pp. 2615-2615, 2020. [4] Li, W., Li, W., Feng, Y. and Yang, C., "Numerical analysis of the back interface for high efficiency wide band gap chalcopyrite solar cells", Solar Energy, Vol. 180, pp. 207-215, 2019. [5] Regmi, G., Ashok, A., Chawla, P., Semalti, P., Velumani, S., Sharma, S. N. and Castaneda, H, "Perspectives of chalcopyrite-based CIGSe thin-film solar cell", a review. Journal of Materials Science: Materials in Electronics, Vol. 31, pp. 7286-7314, 2020. [6] Niki, S., Contreras, M., Repins, I., Powalla, M., Kushiya, K., Ishizuka, S. and Matsubara, K., "CIGS absorbers and processes Progress in Photovoltaics", Research and Applications, Vol. 18, pp. 453-466, 2010. [7] Nakamura, M., Yamaguchi, K., Kimoto, Y., Yasaki, Y., Kato, T., Sugimoto, H. "Cd-free Cu (In, Ga)(Se, S)2 thin-film solar cell with record efficiency of 23.35%", IEEE Journal of Photovoltaics, Vol. 9, pp. 1863-1867, 2019. [8] Kumar, A., Goyal, A. K., Gupta, U., Gupta, N. and Chaujar, R., "Increased efficiency of 23% for CIGS solar cell by using ITO as front contact", Materials Today, Proceedings, Vol. 28, pp. 361-365, 2020. [9] Ghorbani, T., Zahedifar, M., Moradi, M. and Ghanbari, E., "Influence of affinity, band gap and ambient temperature on the efficiency of CIGS solar cells", Optik, Vol. 223, pp. 165541, 2020. [10] AlZoubi, T. and M. Moustafa, "Numerical optimization of absorber and CdS buffer layers in CIGS solar cells using SCAPS", Int. J. Smart Grid Clean Energy, Vol. 8, pp. 291-298, 2019. [11] Bagul, B. Y., "Growth and characterization of cadmium sulphide films synthesized by low cost technique for photovoltaic device applications", Journal of Engineering Sciences, Vol. 11, PP. 356-362, 2020. [12] Tobbeche, S., Kalache, S., Elbar, M., Kateb, M. N. and Serdouk, M. R., "Improvement of the CIGS solar cell performance: structure based on a ZnS buffer layer", Optical and Quantum Electronics, Vol. 51, PP. 1-13, 2019. [13] Moradi, M., Teimouri, R., Saadat, M. and Zahedifar, M., "Buffer layer replacement: a method for increasing the conversion efficiency of CIGS thin film solar cells", Optik, Vol. 136, PP. 222-227,‌ 2017. [14] Barman, B. and Kalita, P. K., "Influence of back surface field layer on enhancing the efficiency of CIGS solar cell", Solar Energy, Vol. 216, PP. 329-337, 2021. [15] Kato, T. Wu, J. Hirai, Y. Sugimoto, H. and Bermudez, V., "Record efficiency for thin-film polycrystalline solar cells up to 22.9% achieved by Cs-treated Cu (In, Ga)(Se, S)2", IEEE Journal of Photovoltaics, Vol. 9, pp. 325-330, 2018. [16] Bouabdelli, M. W., Rogti, F., Maache, M. and Rabehi, A., "Performance enhancement of CIGS thin-film solar cell", Optik, Vol. 216, pp. 164948,‌ 2020. [17] Tobbeche, S., Kalache, S., Elbar, M., Kateb, M. N. and Serdouk, M. R., "Improvement of the CIGS solar cell performance: structure based on a ZnS buffer layer", Optical and Quantum Electronics, Vol. 51, PP. 1-13, 2019. [18] Gray, J. L., The physics of the solar cell. Handbook of photovoltaic science and engineering, Vol. 2, pp. 82-128, 2003. [19] Zhou, W., Nanoimprint lithography: an enabling process for nanofabrication. Springer Science & Business Media, 2013. [20] Hayat, M., Babaji, G., Said, M. and Ahmed, A. B., "Determination of the effect of layer thickness on the efficiency of cigs-based solar cells using Scaps-1d", ACTA Scientific Applied Physics, Vol. 1, PP. 10-15,‌ 2020. [21] Reyes-Banda, M. G., Regalado-Perez, E., Pintor-Monroy, M. I., Hernández-Gutierrez, C. A., Quevedo-López, M. A. and Mathew, X., "Effect of Se diffusion and the role of a thin CdS buffer layer in the performance of a CdSe/CdTe solar cell", Superlattices and Microstructures, Vol. 133, PP. 106219, 2019. [22] Tan, F., Wang, Z., Qu, S., Cao, D., Liu, K., Jiang, Q. and Wang, Z., "A CdSe thin film: a versatile buffer layer for improving the performance of TiO2 nanorod array: PbS quantum dot solar cells", Nanoscale, Vol. 8, PP. 10198-10204,‌ 2016.
Energy Engineering and Management
Volume 12, Issue 3
November 2022
Pages 122-129

Files

Share

How to cite

Statistics